This website uses cookies. By using this site, you consent to the use of cookies. For more information, please take a look at our Privacy Policy.

Images are for reference only,

See Technical Specifications

OPA569AIDWPR

Power Op Amp, Output Signal Swings Within 200mV of Rails at 2A Output Current

Manufacturer:

TI
Mfr.Part #:

OPA569AIDWPR
Datasheet:

OPA569AIDWPR Datasheet (PDF)
Number of channels:

1
Total supply voltage (+5 V = 5, ±5 V = 10) (min) (V):

2.7
Total supply voltage (+5 V = 5, ±5 V = 10) (max) (V):

5.5
Iout (typ) (A):

2.4
EDA/CAD Models:

Request Free CAD Models for OPA569AIDWPR

Email: [email protected]

Skype: live:.cid.ab6b29428937b76

Tel: +852 95804164

OPA569AIDWPR General Description

The OPA569 is a low-cost, high-current, operational amplifier designed for driving a wide variety of loads while operating on low-voltage supplies. It operates from either single or dual supplies for design flexibility and has rail-to-rail swing on the input and output. Typical output swing is within 150mV of the supply rails, with output current of 2A. Output swing closer to the rails is achievable with lighter loads.

The OPA569 is unity gain stable, has low dc errors, is easy to use, and free from the phase inversion problems found in some power amplifiers. High performance is maintained at voltage swings near the output rails.

The OPA569 provides an accurate user-selected current limit that is set with an external resistor, or digitally adjusted via a Digital-to-Analog Converter.

The OPA569 output can be independently disabled using the Enable pin, saving power and protecting the load.

The I_MONITOR pin provides a 1:475 bidirectional copy of the output current. This eliminates the need for a series current shunt resistor, allowing more voltage to be applied to the load. This pin can be used for simple monitoring, or feedback control to establish constant output current.

Two flags are provided: one for warning of thermal over-stress, and one for current limit condition. The Thermal Flag pin can be connected to the Enable pin to provide a thermal shutdown solution.

Packaged in the Texas Instruments PowerPAD package, it is small and easy to heat sink. The OPA569 is specified for operation over the extended industrial temperature range, 40°C to +85°C.

Key Features

HIGH OUTPUT CURRENT: 2A
OUTPUT SWINGS TO: 150mV of Rails with I_O =2A
THERMAL PROTECTION
ADJUSTABLE CURRENT LIMIT
TWO FLAGS: Current Limit and Temperature Warning
LOW SUPPLY VOLTAGE OPERATION: 2.7V to 5.5V
SHUTDOWN FUNCTION WITH OUTPUT DISABLE
SMALL POWER PACKAGE: SO-20 PowerPAD™
APPLICATIONS
- THERMOELECTRIC COOLER DRIVER
- LASER DIODE PUMP DRIVER
- VALVE, ACTUATOR DRIVER
- SYNCHRO, SERVO DRIVER
- TRANSDUCER EXCITATION
- GENERAL LINEAR POWER BOOSTER FOR OP AMPS
- PARALLELING OPTION FOR HIGHER CURRENT APPLICATIONS

PowerPAD is a trademark of Texas Instruments.

Specifications

Number of channels	1	Total supply voltage (+5 V = 5, ±5 V = 10) (min) (V)	2.7
Total supply voltage (+5 V = 5, ±5 V = 10) (max) (V)	5.5	Iout (typ) (A)	2.4
GBW (typ) (MHz)	1.2	Slew rate (typ) (V/µs)	1.2
Vos (offset voltage at 25°C) (max) (mV)	2	Offset drift (typ) (V/°C)	0.0000013
Iq per channel (typ) (mA)	9	Features	Adj Current Limit, Shutdown
Rating	Catalog	Operating temperature range (°C)	-55 to 125
Input bias current (max) (pA)	10	CMRR (typ) (dB)	90
Rail-to-rail	In to V-, Out	Architecture	FET