Payment Method
DAC1280IPWR
Very Low Distortion Digital-to-Analog Converter for Seismic Applications
-
Manufacturer:
-
Mfr.Part #:
DAC1280IPWR
-
Datasheet:
-
Type:
DAC
-
Number of Channels:
1
-
Data Interface:
Serial
-
Voltage Supply Source:
Analog and Digital, Dual ±
-
EDA/CAD Models:
Availability: 7612 PCS
Please fill in the short form below and we will provide you the quotation immediately.
DAC1280IPWR General Description
The DAC1280 is a very low distortion digital-to-analog converter (DAC) suited for performance testing of seismic equipment. The DAC1280 provides a high-accuracy output signal from a bitstream input. The device achieves very high linearity in a small package while dissipating only 18mW. Together with the high-performance ADS1281 and ADS1282 analog-to-digital converters (ADCs), these devices create a test and measurement system that meets the exacting demands of energy exploration and seismic monitoring equipment.
The DAC1280 is designed to match the system components (power supply, clock and reference voltage) of the companion ADCs, the ADS1281 and ADS1282. The input to the DAC1280 is a 1s density modulated bitstream. The DAC1280 output is a differential current intended for use with an active I/V converter. The I/V converter provides a voltage output suitable for performance testing of sensors and ADCs.
Three gain control pins set the output range in 6dB steps from 0dB to –36db (±2.5V to ±0.039V differential). The attenuation ranges match the gains of the ADS1282 for testing at all gains. The DAC uses a reference voltage and bias resistor to set the full-scale output. The resistor can be adjusted to fine-trim the DAC full-scale.
The SYNC pin aligns the input data sampling to the CLK phase. A power-down pin shuts down the device when not in use. The DAC1280 is available in a small, 16-pin TSSOP package and is fully specified for operation over –40°C to +85°C temperature range with a maximum operating temperature of +125°C.
Key Features
- Outstanding Performance:
- THD: –125dB
- SNR: 120dB (413Hz BW, Gain = 1/1)
- Gain Error: 0.1%
- Pin Operation: No Registers to Program
- Gain: 1/1 to 1/64
- SYNC Input for Phase Control
- Power-Down Mode
- Low Power: 18mW
- Analog Supply: +5V or ±2.5V
- Digital Supply: 1.8V to 3.3V
- Small 16-Pin TSSOP Package
- Temperature Range: –40°C to +85°C
- APPLICATIONS
- Energy Exploration Equipment
- Seismic Monitoring Systems
All other trademarks are the property of their respective owners
Specifications
Category | Integrated Circuits (ICs)Data AcquisitionADCs/DACs - Special Purpose | Series | - |
Type | DAC | Number of Channels | 1 |
Resolution (Bits) | - | Sampling Rate (Per Second) | - |
Data Interface | Serial | Voltage Supply Source | Analog and Digital, Dual ± |
Voltage - Supply | ±2.5V, 5V, 1.8V ~ 3.3V | Operating Temperature | -40°C ~ 125°C |
Mounting Type | Surface Mount | Base Product Number | DAC1280 |
Service Policies and Others
After-Sales & Settlement Related
For alternative payment channels, please reach out to us at:
[email protected]Shipping Method
AVAQ determines and packages all devices based on electrostatic discharge (ESD) and moisture sensitivity level (MSL) protection requirements.
365-Day Product
Quality Guarantee
We promise to provide 365 days quality assurance service for all our products.
Availability: 7612 PCS
+BOMQty. | Unit Price | Ext. Price |
---|---|---|
1+ | - | - |
The prices below are for reference only.
All bill of materials (BOM) can be sent via email to [email protected], or fill below form to Quote for DAC1280IPWR, guaranteed quotes back within 12hr.
Top Sellers
-
ADS1248IPWR
Texas Instruments
100+ $3.702
-
ADS1115IDGST
Texas Instruments
1000+ $1.850
-
ADS1115IDGSR
Texas Instruments
1000+ $1.131
-
ADS1248IPW
TI
24 Bit Analog to Digital Converter 4, 7 Input 1 Sigma-Delta 28-TSSOP
-
LM2917N
Texas Instruments
Frequency-to-voltage converter for ground or supply referred load up to 50-mA (with Zener regulat