Payment Method
AD8362ARU-REEL
RF Detector 2700MHz 16-Pin TSSOP T/R
-
Manufacturer:
-
Mfr.Part #:
AD8362ARU-REEL
-
Datasheet:
-
Frequency:
50Hz ~ 3.8GHz
-
RF Type:
Cellular, GSM, CDMA, TDMA, TETRA
-
Input Range:
-52dBm ~ 8dBm
-
Accuracy:
±0.5dB
-
EDA/CAD Models:
Availability: 3708 PCS
Please fill in the short form below and we will provide you the quotation immediately.
AD8362ARU-REEL General Description
The AD8362 is a true rms-responding power detector that has a 65 dB measurement range. It is intended for use in a variety of high frequency communication systems and in instrumentation requiring an accurate response to signal power. It is easy to use, requiring only a single supply of 5 V and a few capacitors. It operates from arbitrarily low frequencies to over 3.8 GHz and accepts inputs from −52 dBm to +8 dBm with crest factors that are typical of quadrature amplitude modulation (QAM) and orthogonal frequency division multiplexing (OFDM) modulation schemes.
The input signal is applied to a resistive ladder attenuator that comprises the input stage of a variable gain amplifier (VGA). The 12 tap points are smoothly interpolated using a proprietary technique to provide a continuously variable attenuator, which is controlled by a voltage applied to the VSET pin. The resulting signal is applied to a high performance broadband amplifier. Its output is measured by an accurate square-law detector cell. The fluctuating output is then filtered and compared with the output of an identical squarer, whose input is a fixed dc voltage applied to the VTGT pin, usually the accurate reference of 1.25 V pro-vided at the VREF pin.
The difference in the outputs of these squaring cells is integrated in a high gain error amplifier, generating a voltage at the VOUT pin with rail-to-rail capabilities. In a controller mode, this low noise output can be used to vary the gain of a host system’s RF amplifier, thus balancing the setpoint against the input power. Optionally, the voltage at VSET can be a replica of the RF signal’s amplitude modulation, in which case the overall effect is to remove the modulation component prior to detection and low-pass filtering. The corner frequency of the averaging filter can be lowered without limit by adding an external capacitor at the CLPF pin. The AD8362 can be used to determine the true power of a high frequency signal having a complex low frequency modulation envelope, or simply as a low frequency rms volt-meter. The high-pass corner generated by its offset-nulling loop can be lowered by a capacitor added on the CHPF pin.
Used as a power measurement device, VOUT is strapped to VSET. The output is then proportional to the logarithm of the rms value of the input. In other words, the reading is presented directly in decibels and is conveniently scaled 1 V per decade, or 50 mV/dB; other slopes are easily arranged. In controller modes, the voltage applied to VSET determines the power level required at the input to null the deviation from the setpoint. The output buffer can provide high load currents.
The AD8362 has 1.3 mW power consumption when powered down by a logic high applied to the PWDN pin. It powers up within about 20 μs to its nominal operating current of 20 mA at 25°C. The AD8362 is supplied in a 16-lead TSSOP for operation over the temperature range of −40°C to +85°C.
Key Features
- Complete fully calibrated measurement/control system
- Accurate rms-to-dc conversion from 50 Hz to 3.8 GHz
- Input dynamic range of >65 dB: −52 dBm to +8 dBm in 50 Ω
- Waveform and modulation independent, such as GSM/CDMA/TDMA
- Linear-in-decibels output, scaled 50 mV/dB
- Law conformance error of 0.5 dB
- All functions temperature and supply stable
- Operates from 4.5 V to 5.5 V at 24 mA
- Power-down capability to 1.3 mW
Application
- Power amplifier linearization/control loops
- Transmitter power controls
- Transmitter signal strength indication (TSSI)
- RF instrumentation
Specifications
Category | RF and WirelessRF Detectors | Series | - |
Frequency | 50Hz ~ 3.8GHz | RF Type | Cellular, GSM, CDMA, TDMA, TETRA |
Input Range | -52dBm ~ 8dBm | Accuracy | ±0.5dB |
Voltage - Supply | 4.5V ~ 5.5V | Current - Supply | 20 mA |
Mounting Type | Surface Mount |
Service Policies and Others
After-Sales & Settlement Related
For alternative payment channels, please reach out to us at:
[email protected]Shipping Method
AVAQ determines and packages all devices based on electrostatic discharge (ESD) and moisture sensitivity level (MSL) protection requirements.
365-Day Product
Quality Guarantee
We promise to provide 365 days quality assurance service for all our products.
Availability: 3708 PCS
+BOMQty. | Unit Price | Ext. Price |
---|---|---|
1+ | - | - |
The prices below are for reference only.
All bill of materials (BOM) can be sent via email to [email protected], or fill below form to Quote for AD8362ARU-REEL, guaranteed quotes back within 12hr.
Top Sellers
-
ADF4355
ADI
Phase Locked Loops - PLL Wideband PLL w/ int ultra low noise VCO
-
HMC424ALP3E
Analog Devices, Inc
6Bit 0.5dBStep 31.5dB 13GHz 16-Pin LFCSP EP Cut Tape
-
HMC451LC3
ADI
Medium Power Amplifier SMT, 5 - 20 GHz
-
HMC998APM5E
Analog Devices, Inc
RF Amp Single Power Amp 22GHz 15V 32-Pin LFCSP EP Cut Tape
-
HMC451
Analog Devices, Inc
RF Amplifier IC VSAT 5GHz ~ 20GHz Die