This website uses cookies. By using this site, you consent to the use of cookies. For more information, please take a look at our Privacy Policy.

Images are for reference only,

See Technical Specifications

UCC38501DW

PFC IC Average Current 100kHz 20-SOIC

Manufacturer:

Texas Instruments, Inc
Mfr.Part #:

UCC38501DW
Datasheet:

UCC38501DW Datasheet (PDF)
Topology:

Boost
Control mode:

CCM
Switching frequency (max) (kHz):

200
UVLO thresholds on/off (V):

10.5/10
EDA/CAD Models:

Request Free CAD Models for UCC38501DW

Email: [email protected]

Skype: live:.cid.ab6b29428937b76

Tel: +852 95804164

UCC38501DW General Description

The UCC2850x family provides all of the control functions necessary for an active power-factor-corrected preregulator and a second-stage dc-to-dc converter. The controller achieves near-unity power factor by shaping the ac input line current waveform to correspond to the ac input-line voltage using average current-mode control. The dc-to-dc converter uses peak current-mode control to perform the step-down power conversion.

The PFC stage is leading-edge modulated while the second stage is trailing-edge synchronized to allow for minimum overlap between the boost and PWM switches. This reduces ripple current in the bulk-output capacitor.In order to operate with over three-to-one range of input-line voltages, a line feedforward (V_FF) is used to keep input power constant with varying input voltage. Generation of V_FF is accomplished using I_AC in conjunction with an external single-pole filter. This not only reduces external parts count, but also avoids the use of high-voltage components, offering a lower-cost solution. The multiplier then divides the line current by the square of V_FF.

The UCC2850x PFC section incorporates a low offset-voltage amplifier with 7.5-V reference, a highly-linear multiplier capable of a wide current range, a high-bandwidth, low offset-current amplifier, with a novel noise-attenuation configuration, PWM comparator and latch, and a high-current output driver. Additional PFC features include over-voltage protection, zero-power detection to turn off the output when VAOUT is below 0.33 V and peak current and power limiting.

The dc-to-dc section relies on an error signal generated on the secondary-side and processes it by performing peak current mode control. The dc-to-dc section also features current limiting, a controlled soft-start, preset operating range with selectable options, and 50% maximum duty cycle.

The UCC28500 and UCC28502 have a wide PFC-UVLO threshold (16.5 V/10 V) for bootstrap bias supply operation. The UCC28501 and UCC28503 are designed with a narrow UVLO range (10.5 V/10 V) more suitable for fixed bias operation. The UCC28500 and UCC28501 have a narrow UVLO threshold for PWM stage (to allow operation down to 75% of nominal bulk voltage), while the UCC28502 and UCC38503 are configured for a much wider operation range for the PWM stage (down to 50% of bulk nominal voltage).

Available in 20-pin N and DW packages.

Texas Instruments, IncMicrosoft.AspNetCore.Mvc.Localization.LocalizedHtmlString

Key Features

Combines PFC and Downstream Converter Controls
Controls Boost Preregulator to Near-Unity Power Factor
Accurate Power Limiting
Improved Feedforward Line Regulation
Peak Current-Mode Control in Second Stage
Programmable Oscillator
Leading-Edge/Trailing-Edge Modulation for Reduced Output Ripple
Low Start-up Supply Current
Synchronized Second Stage Start-Up, with Programmable Soft-start
Programmable Second Stage Shutdown

Specifications

Topology	Boost	Control mode	CCM
Switching frequency (max) (kHz)	200	UVLO thresholds on/off (V)	10.5/10
Vin (max) (V)	18	Features	< 150 W applications, Average current mode, Continuous Control Mode, Enable, Overvoltage protection, Supports Flyback
Rating	Catalog	Operating temperature range (°C)	0 to 70
Duty cycle (max) (%)	100	Pin Count	20
Released Date	Apr 14, 2021	Last Modified Date	Mar 7, 2023 4:10 PM UTC