This website uses cookies. By using this site, you consent to the use of cookies. For more information, please take a look at our Privacy Policy.

Images are for reference only,

See Technical Specifications

BQ24751ARHDR

Charger IC Multi-Chemistry 28-VQFN (5x5)

Manufacturer:

TI
Mfr.Part #:

BQ24751ARHDR
Datasheet:

BQ24751ARHDR Datasheet (PDF)
Pbfree Code:

Yes
Part Life Cycle Code:

Active
Pin Count:

28
Reach Compliance Code:

compliant
EDA/CAD Models:

Request Free CAD Models for BQ24751ARHDR

Email: [email protected]

Skype: live:.cid.ab6b29428937b76

Tel: +852 95804164

BQ24751ARHDR General Description

The bq24751A is a high-efficiency, synchronous battery charger with integrated compensation and system power selector logic, offering low component count for space-constrained multi-chemistry battery charging applications. Ratiometric charge current and voltage programming allows very high regulation accuracies, and can be either hardwired with resistors or programmed by the system power-management microcontroller using a DAC or GPIOs.

The bq24751A charges two, three, or four series Li+ cells, supporting up to 10 A of charge current, and is available in a 28-pin, 5x5-mm thin QFN package.

The bq24751A controls external switches to prevent battery discharge back to the input, connect the adapter to the system, and to connect the battery to the system using 6-V gate drives for better system efficiency. For maximum system safety, inrush-power limiting provides instantaneous response to high input voltage multiplied by current. This AC Over-Power protection (ACOP) feature limits the input-switch power to the programmed level on the ACOP pin, and latches off if the high-power condition persists to prevent overheating.

The bq24751A features Dynamic Power Management (DPM) and input power limiting. These features reduce battery charge current when the input power limit is reached to avoid overloading the AC adapter when supplying the load and the battery charger simultaneously. A highly-accurate current-sense amplifier enables precise measurement of input current from the AC adapter to monitor the overall system power.

Key Features

NMOS-NMOS Synchronous Buck Converter with 300 kHz Frequency and >95% Efficiency
30-ns Minimum Driver Dead-time and 99.5% Maximum Effective Duty Cycle
High-Accuracy Voltage and Current Regulation
- ±0.5% Charge Voltage Accuracy
- ±3% Charge Current Accuracy
- ±3% Adapter Current Accuracy
- ±2% Input Current Sense Amp Accuracy
Integration
- Automatic System Power Selection From AC/DC Adapter or Battery
- Internal Loop Compensation
- Internal Soft Start
Safety
- Programmable Input Overvoltage Protection (OVP)
- Dynamic Power Management (DPM) with Status Indicator
- Programmable Inrush Adapter Power (ACOP) and Overcurrent (ACOC) Limits
- Reverse-Conduction Protection Input FET
Supports Two, Three, or Four Li+ Cells
5 - 24 V AC/DC-Adapter Operating Range
Analog Inputs with Ratiometric Programming via Resistors or DAC/GPIO Host Control
- Charge Voltage (4-4.512 V/cell)
- Charge Current (up to 10 A, with 10-m sense resistor)
- Adapter Current Limit (DPM)
Status and Monitoring Outputs
- AC/DC Adapter Present with Programmable Voltage Threshold
- Current Drawn from Input Source
Battery Learn Cycle Control
Supports Any Battery Chemistry: Li+, NiCd, NiMH, Lead Acid, etc.
Charge Enable
28-pin, 5x5-mm QFN package
Energy Star Low I_q
- < 10-µA Off-State Battery Discharge Current
- < 1.5-mA Off-State Input Quiescent Current
APPLICATIONS
- Notebook and Ultra-Mobile Computers
- Portable Data Capture Terminals
- Portable Printers
- Medical Diagnostics Equipment
- Battery Bay Chargers
- Battery Back-up Systems

Specifications

Source Content uid	BQ24751ARHDR	Pbfree Code	Yes
Part Life Cycle Code	Active	Pin Count	28
Reach Compliance Code	compliant	ECCN Code	EAR99
HTS Code	8542.39.00.01	Adjustable Threshold	YES
Analog IC - Other Type	POWER SUPPLY SUPPORT CIRCUIT	JESD-30 Code	S-PQCC-N28
Moisture Sensitivity Level	2	Number of Channels	1
Number of Functions	1	Number of Terminals	28
Peak Reflow Temperature (Cel)	260	Surface Mount	YES
Switcher Configuration	BUCK	Temperature Grade	AUTOMOTIVE
Terminal Finish	NICKEL PALLADIUM GOLD	Terminal Form	NO LEAD
Terminal Position	QUAD	Time@Peak Reflow Temperature-Max (s)	30