This website uses cookies. By using this site, you consent to the use of cookies. For more information, please take a look at our Privacy Policy.

Images are for reference only,

See Technical Specifications

S5688N +BOM

Rectifier Diode Si 1KV 1A 2-Pin Case M1A

Manufacturer:

EIC Semiconductor
Mfr.Part #:

S5688N
Datasheet:

S5688N Datasheet (PDF)
Feature-pin-count:

2
Feature-military:

No
Feature-aec-qualified:

No
Feature-auto-motive:

No

Email: [email protected]

Skype: live:.cid.ab6b29428937b76

Tel: +852 95804164

Key Features

Digital Signal Controller Core
Efficient 16-bit 56800E family Digital Signal Controller (DSC) engine with dual Harvard architecture
As many as 32 Million Instructions Per Second (MIPS) at 32MHz core frequency
Single-cycle 16 ×16-bit parallel Multiplier-Accumulator (MAC)
Four 36-bit accumulators, including extension bits
32-bit arithmetic and logic multi-bit shifter
Parallel instruction set withunique DSP addressing modes
Hardware DO and REP loops
Three internal address buses
Four internal data buses
Instruction set supports both DSP and controller functions
Controller-style addressing modes and instructions for compact code
Efficient C compiler and local variable support
Software subroutine and interrupt stack with depth limited only by memory
JTAG/Enhanced On-Chip Emulation (OnCE) for unobtrusive, processor speed-independent, real-time debugging
Memory
Dual Harvard architecture permits as many as three simultaneous accesses to program and data memory
Flash security and protection that prevent unauthorized users from gaining access to the internal Flash
On-chip memory:
— 16KB of Program Flash (56F8013 device)
12KB of Program Flash (56F8011 device)
— 4KB of Unified Data/Program RAM (56F8013 device)
2KB of Unified Data/ProgramRAM (56F8011 device)
EEPROM emulation capability using Flash
Peripheral Circuits for 56F8013/56F8011
One multi-function six-output Pulse Width Modulator (PWM) module
— Up to 96MHz PWM operating clock
— 15 bits of resolution
— Center-aligned and Edge-aligned PWM signal mode
— Four programmable fault inputs with programmable digital filter
— Double-buffered PWM registers
— Each complementary PWM signal pair can outputdifferent switching frequency by selecting PWM generation sources from:
– PWM generator
– External GPIO
– Internal timers
– ADC conversion resultof over/under limits:
– When the conversion result is greater than high limit, deactivate PWM signal
– When the conversion result is less than low limit, activate the PWM signal
Two independent 12-bit Analog-to-Digital Converters (ADCs)
— 2 x 3 channel inputs
— Supports both simultaneous and sequential conversions
— ADC conversions can be synchronized by both PWM and timer modules
— Sampling rate up to 2.67MSPS
— 8-word result buffer registers
— ADC Smart Power Management (Auto-standby, auto-powerdown)
One 16-bit multi-purpose Quad Timer module (TMR)
— Up to 96MHz operating clock
— Four independent 16-bit counter/timers with cascading capability
— Each timer has capture and compare capability
— Up to 12 operating modes
One Serial Communication Interface (SCI) with LIN Slave functionality
— Full-duplex or single-wire operation
— Two receiver wake-up methods:
– Idle line
– Address mark
One Serial Peripheral Interface (SPI)
— Full-duplex operation
— Master and slave modes
— Programmable Length Transactions (2 to 16 bits)
One Inter-Integrated Circuit (I2C) port
— Operates up to 400kbps
— Supports both master and slave operation
Computer Operating Properly (COP)/Watchdog timer capable of selecting different clock sources

Specifications

feature-packaging		feature-rad-hard
feature-pin-count	2	feature-cecc-qualified
feature-esd-protection		feature-military	No
feature-aec-qualified	No	feature-auto-motive	No
feature-p-pap	No	feature-eccn-code	EAR99
feature-svhc		feature-svhc-exceeds-threshold	No