This website uses cookies. By using this site, you consent to the use of cookies. For more information, please take a look at our Privacy Policy.

Images are for reference only,

See Technical Specifications

LM73100RPWR

OR Controller N-Channel Single 0.0284Ohm 10-Pin VQFN-HR T/R

Manufacturer:

TI
Mfr.Part #:

LM73100RPWR
Datasheet:

LM73100RPWR Datasheet (PDF)
Vin (min) (V):

2.7
Vin (max) (V):

23
Number of channels:

1
Features:

Analog current monitor, Gate ON/OFF control, Overvoltage protection, Power good signal, Reverse current blocking, Reverse polarity protection, Short circuit protection, Thermal shutdown
EDA/CAD Models:

Request Free CAD Models for LM73100RPWR

Email: [email protected]

Skype: live:.cid.ab6b29428937b76

Tel: +852 95804164

LM73100RPWR General Description

The LM73100 is a highly integrated circuit protection and power management solution in a small package. The device provides multiple protection modes using very few external components and is a robust defense against voltage surges, reverse polarity, reverse current and excessive inrush current.

With integrated back-to-back FETs, reverse current flow from output to input is blocked at all times, making the device well suited for power MUX/ORing applications. The device uses linear ORing based scheme to ensure almost zero DC reverse current and emulates ideal diode behavior with minimum forward voltage drop and power dissipation.

Applications with particular inrush current requirements can set the output slew rate with a single external capacitor. Loads are protected from input overvoltage conditions by cutting off the output if input exceeds an adjustable overvoltage threshold. The device also provides fast trip response to transient overcurrent events during steady state.

The device provides an accurate sense of the output load current on the analog current monitor pin.

The device is available in a 2-mm x 2-mm, 10-pin HotRod QFN package for improved thermal performance and reduced system footprint.

The device is characterized for operation over a junction temperature range of –40°C to +125°C.

Key Features

Wide operating input voltage range: 2.7 V to 23 V
- 28-V absolute maximum
- Withstands negative voltages up to -15 V
Integrated back-to-back FETs with low On-Resistance: R_ON = 28.4 mΩ (typ)
Ideal diode operation with true reverse current blocking
Fast overvoltage protection
- 1.2-µs (typ) response time
- Adjustable overvoltage lockout (OVLO)
Fast-trip response to transient overcurrents during steady state
- 500-ns (typ) response time
- Latch-off after fault
Analog load current monitor output (IMON)
- Current range: 0.5 A to 5.5 A
- Accuracy: ±15% (max) (I_OUT ≥ 1 A)
Active high enable input with adjustable undervoltage lockout threshold (UVLO)
Adjustable output slew rate control (dVdt)
Overtemperature protection
Power Good indication (PG) with adjustable threshold (PGTH)
Small footprint: QFN 2 mm x 2 mm, 0.45-mm pitch

Specifications

Vin (min) (V)	2.7	Vin (max) (V)	23
Number of channels	1	Features	Analog current monitor, Gate ON/OFF control, Overvoltage protection, Power good signal, Reverse current blocking, Reverse polarity protection, Short circuit protection, Thermal shutdown
Iq (typ) (mA)	0.4	Iq (max) (mA)	0.6
FET	Integrated single FET	Operating temperature range (°C)	-40 to 125
IReverse (typ) (µA)	4.8	Design support	Calculation Tool, EVM, Simulation Model
Rating	Catalog	Imax (A)	5.5
Shutdown current (ISD) (mA) (A)	0.0046	Device type	Ideal diode controller
Product type	Ideal diode controller