This website uses cookies. By using this site, you consent to the use of cookies. For more information, please take a look at our Privacy Policy.


LVDS Interface IC Mil Enhance Hi Spd Diff Receivers

Inquiry Add To Bom

V62/05614-01XE General Description

This family of four LVDS data line receivers offers the widest common-mode input voltage range in the industry. These receivers provide an input voltage range specification compatible with a 5-V PECL signal as well as an overall increased ground-noise tolerance. They are in industry standard footprints with integrated termination as an option.

Precise control of the differential input voltage thresholds allows for inclusion of 50 mV of input voltage hysteresis to improve noise rejection on slowly changing input signals. The input thresholds are still no more than +50 mV over the full input common-mode voltage range.

The high-speed switching of LVDS signals usually necessitates the use of a line impedance matching resistor at the receiving-end of the cable or transmission media. The SN65LVDT series of receivers eliminates this external resistor by integrating it with the receiver. The nonterminated SN65LVDS series is also available for multidrop or other termination circuits.

The receivers can withstand ±15-kV human-body model (HBM) and ±600-V machine model (MM) electrostatic discharges to the receiver input pins with respect to ground without damage. This provides reliability in cabled and other connections where potentially damaging noise is always a threat.

The receivers also include a (patent pending) failsafe circuit that provides a high-level output within 600 ns after loss of the input signal. The most common causes of signal loss are disconnected cables, shorted lines, or powered-down transmitters. The failsafe circuit prevents noise from being received as valid data under these fault conditions. This feature may also be used for Wired-Or bus signaling. See The Active Failsafe Feature of the SN65LVDS32B application note.

The intended application and signaling technique of these devices is point-to-point baseband data transmission over controlled impedance media of approximately 100 . The transmission media may be printed-circuit board traces, backplanes, or cables. The ultimate rate and distance of data transfer is dependent upon the attenuation characteristics of the media and the noise coupling to the environment.

The SN65LVDS33-EP is characterized for operation from -55°C to 125°C.

Texas Instruments, Inc Inventory

Key Features

  • Controlled Baseline — One Assembly/Test Site, One Fabrication Site
  • Extended Temperature Performance of Up to -55°C to 125°C
  • Enhanced Diminishing Manufacturing Sources (DMS) Support
  • Enhanced Product-Change Notification
  • Qualification Pedigree(1)
  • 400-Mbps Signaling Rate(2) and 200-Mxfr/s Data Transfer Rate
  • Operates With a Single 3.3-V Supply
  • -4-V to 5-V Common-Mode Input Voltage Range
  • Differential Input Thresholds < ±50 mV With 50 mV of Hysteresis Over Entire Common-Mode Input Voltage Range
  • Integrated 110- Line Termination Resistors On LVDT Products
  • Complies With TIA/EIA-644 (LVDS)
  • Active Failsafe Assures a High-Level Output With No Input
  • Bus-Pin ESD Protection Exceeds 15-kV HBM
  • Input Remains High-Impedance On Power Down
  • TTL Inputs Are 5-V Tolerant
  • Pin-Compatible With the AM26LS32, SN65LVDS32B, μA9637, SN65LVDS9637B

(1) Component qualification in accordance with JEDEC and industry standards to ensure reliable operation over an extended temperature range. This includes, but is not limited to, Highly Accelerated Stress Test (HAST) or biased 85/85, temperature cycle, autoclave or unbiased HAST, electromigration, bond intermetallic life, and mold compound life. Such qualification testing should not be viewed as justifying use of this component beyond specified performance and environmental limits.
(2) The signaling rate of a line is the number of voltage transitions that are made per second expressed in the units bps (bits per second).

Texas Instruments, Inc Original Stock
Texas Instruments, Inc Inventory


Function Receiver Protocols LVDS
Number of transmitters 0 Number of receivers 4
Supply voltage (V) 3.3 Signaling rate (MBits) 400
Rating HiRel Enhanced Product

Service Policies and Others

After-Sales & Settlement Related

payment Payment

We accept TT prepayment (bank transfer), paypal, credit cards, Western Union, Money Gram.

If you have specific preferences or requirements for payment channels, please contact our sales team. 

customers are required to pay all possible fees, including sales tax,customs fees, etc.

shipping Shipping And Packing
Shipping Method

Our products are mainly transported and delivered by DHL, FedEx, UPS and other logistics partners on site -- Available to 200+ countries.


AVAQ determines and packages all devices based on electrostatic discharge (ESD) and moisture sensitivity level (MSL) protection requirements.

warranty Warranty & Returns

Our policies and procedures are designed to ensure compliance with various quality specifications and to quickly resolve quality-related issues.

We promise to provide 365 days quality assurance service for all our products.

If you have any dissatisfaction with the quality of the product you received, you can contact us for a refund or exchange, as long as the product is kept in its original condition.


You need to log in to reply. Sign In | Sign Up

Availability: 7034 PCS

Qty. Unit Price(USD) Ext. Price
1+ $4.661 $4.66
200+ $1.804 $360.80
500+ $1.741 $870.50
1000+ $1.710 $1,710.00

The prices below are for reference only.