Key Features

• Operating Conditions
• 4.5V to 5.5V, -40ºC to +85ºC, DC to 70 MIPS
• 4.5V to 5.5V, -40ºC to +125ºC, DC to 60 MIPS
• 4.5V to 5.5V, -40ºC to +150ºC, DC to 40 MIPS
• dsPIC33E Core
• Code-Efficient (C and Assembly) Architecture
• Two 40-Bit Wide Accumulators
• Single-Cycle (MAC/MPY) with Dual Data Fetch
• Single-Cycle, Mixed-Sign MUL plus Hardware Divide
• 32-Bit Multiply Support
• Provides a boot Flash segment in addition to the existing general Flash segment
• Error Code Correction (ECC) for Flash
• Added Two Alternate Register Sets for Fast Context Switching
• Up to Six Pulse-Width Modulation (PWM) Outputs (three generators)
• High-Speed PWM
• Primary Master Time Base Inputs allow Time Base Synchronization from Internal/External Sources
• Dead Time for Rising and Falling Edges
• 8.3 ns PWM Resolution at 60 MIPS,
• 16.6 ns Center-Aligned mode at 60 MIPS
• PWM support DC/DC, AC/DC, inverters, Power Factor Correction (PFC) and lighting
• PWM support Brushless Direct Current (BLDC), Permanent Magnet Synchronous Motor (PMSM), AC Induction Motor (ACIM), Switched Reluctance Motor (SRM)
• Programmable Fault inputs
• Flexible trigger configurations for Analog-to-Digital conversion
• Independent Time Base
• Supports PWM lock, PWM output chopping and dynamic phase shifting
• Integrated Analog Features
• ADC configurable as 10-bit, 1.1 Msps with four S&H or 12-bit, 500 ksps with one S&H
• Up to 36 analog inputs
• Flexible and Independent ADC Trigger Sources
• Up to Four Op Amp/Comparators with Direct Connection to the ADC module:
• Additional dedicated comparator and 7-bit Digital-to-Analog Converter (DAC)
• Programmable references with 128 voltage points
• Programmable blanking and filtering
• Charge Time Measurement Unit
• Supports mTouch™ capacitive touch sensing
• Provides high-resolution time measurement (1 ns)
• On-chip temperature measurement
• Temperature sensor diode
• Multiple sources of edge input triggers
• Timers/Output Compare/Input Capture
• Up to nine general purpose timers
• Five 16-bit or up to two 32-bit timers/counters, Timer3 can provide ADC trigger
• Oscillator Frequency Monitoring through CTMU
• Four Output Capture modules configurable as timers/counters
• Four Input Capture modules
• Communication Interfaces
• Support for LIN/J2602 bus support and IrDA®
• High and low speed (SCI)
• 25 Mbps data rate without PPS used
• One I2C™ module (up to 1 Mbaud) with SMBus Support
• Two SENT J2716 (Single Edge Nibble Transmission-Transmit/Receive) module for Automotive Applications
• Direct Memory Access (DMA)
• 4-Channel DMA with User-Selectable Priority Arbitration
• Universal Asynchronous Receiver/Transmitter (UART), Serial Peripheral Interface (SPI), ADC, Input Capture, Output Compare
• Qualification and Class B Support
• AEC-Q100 Grade 1 (-40ºC to +125ºC)
• AEC-Q100 Grade 0 (-40ºC to +150ºC)
• Class B Safety Library, IEC 60730
• Functional Safety Features
• Backup FRC
• Windowed WDT uses LPRC
• Windowed Deadman Timer uses System Clock (System Windowed Watchdog Timer)
• H/W Clock Monitor Circuit
• Dedicated PWM Fault Pin
• Lockable Clock Configuration
• Functional Safety support (ISO26262)
• ASIL-B focused applications
• FMEDA and Safety manual
• XC16 Functional Safety Compiler
• Functional Safety hardware features
• Flash with Error Correction Code (ECC)
• CodeGuard™ Memory Protection
• On-chip Regulator for CPU
• Backup FRC and redundant clock sources
• Fail Safe Clock Monitor
• Windowed Watchdog Timer (WDT)
• Windowed Deadman Timer (DMT)
• Oscillator Frequency Monitoring through CTMU (OSCI, SYSCLK, FRC, BFRC, LPRC)
• BOR and POR
• Analog peripherals redundancies
• Cyclical Redundancy Check (CRC)
• Illegal Opcode Detection
• PWM Lock and Dedicated PWM Fault Pin
• Internal Loopback to test communication peripherals and IO ports
• SFR and Configuration Locks
• Address Trap
• Math Error Trap
• Redundant data storage for Flash-based Configuration bits and Peripheral Pin Select (PPS) Configuration bits