This website uses cookies. By using this site, you consent to the use of cookies. For more information, please take a look at our Privacy Policy.

Images are for reference only,

See Technical Specifications

DSPIC33EV128GM002-H/SP +BOM

Product Description: 16-Bit 5V Digital Signal Controller with 128KB ECC Flash

Manufacturer:

Microchip Technology, Inc
Mfr.Part #:

DSPIC33EV128GM002-H/SP
Datasheet:

DSPIC33EV128GM002-H/SP Datasheet (PDF)
Series:

Automotive, AEC-Q100, dsPIC™ 33EV, Functional Safety (FuSa)
Core Processor:

dsPIC
Core Size:

16-Bit
Speed:

40 MIPs
EDA/CAD Models:

Request Free CAD Models for DSPIC33EV128GM002-H/SP

DSPIC33EV128GM002-H/SP General Description

dsPIC Automotive, AEC-Q100, dsPIC™ 33EV, Functional Safety (FuSa) Microcontroller IC 16-Bit 40 MIPs 128KB (43K x 24) FLASH 28-SPDIP

Key Features

Operating Conditions
4.5V to 5.5V, -40ºC to +85ºC, DC to 70 MIPS
4.5V to 5.5V, -40ºC to +125ºC, DC to 60 MIPS
4.5V to 5.5V, -40ºC to +150ºC, DC to 40 MIPS
dsPIC33E Core
Code-Efficient (C and Assembly) Architecture
Two 40-Bit Wide Accumulators
Single-Cycle (MAC/MPY) with Dual Data Fetch
Single-Cycle, Mixed-Sign MUL plus Hardware Divide
32-Bit Multiply Support
Provides a boot Flash segment in addition to the existing general Flash segment
Error Code Correction (ECC) for Flash
Added Two Alternate Register Sets for Fast Context Switching
High-Speed PWM
Up to Six Pulse-Width Modulation (PWM) Outputs (three generators)
Primary Master Time Base Inputs allow Time Base Synchronization from Internal/External Sources
Dead Time for Rising and Falling Edges
8.3 ns PWM Resolution at 60 MIPS,
16.6 ns Center-Aligned mode at 60 MIPS
PWM support for DC/DC, AC/DC, inverters, Power Factor Correction (PFC) and lighting
PWM support for Brushless Direct Current (BLDC), Permanent Magnet Synchronous Motor (PMSM), AC Induction Motor (ACIM), Switched Reluctance Motor (SRM)
Programmable Fault inputs
Flexible trigger configurations for Analog-to-Digital conversion
Independent Time Base
Supports PWM lock, PWM output chopping and dynamic phase shifting
Integrated Analog Features
ADC configurable as 10-bit, 1.1 Msps with four S&H or 12-bit, 500 ksps with one S&H
Up to 36 analog inputs
Flexible and Independent ADC Trigger Sources
Up to Four Op Amp/Comparators with Direct Connection to the ADC module:
Additional dedicated comparator and 7-bit Digital-to-Analog Converter (DAC)
Programmable references with 128 voltage points
Programmable blanking and filtering
Charge Time Measurement Unit
Supports mTouch™ capacitive touch sensing
Provides high-resolution time measurement (1 ns)
On-chip temperature measurement
Temperature sensor diode
Multiple sources of edge input triggers
Timers/Output Compare/Input Capture
Up to nine general purpose timers
Five 16-bit or up to two 32-bit timers/counters, Timer3 can provide ADC trigger
Four Output Capture modules configurable as timers/counters
Four Input Capture modules
Communication Interfaces
Support for LIN/J2602 bus support and IrDA®
High and low speed (SCI)
25 Mbps data rate without PPS used
One I2C™ module (up to 1 Mbaud) with SMBus Support
Two SENT J2716 (Single Edge Nibble Transmission-Transmit/Receive) module for Automotive Applications
Direct Memory Access (DMA)
4-Channel DMA with User-Selectable Priority Arbitration
Universal Asynchronous Receiver/Transmitter (UART), Serial Peripheral Interface (SPI), ADC, Input Capture, Output Compare
Qualification and Class B Support
AEC-Q100 Grade 1 (-40ºC to +125ºC)
AEC-Q100 Grade 0 (-40ºC to +150ºC)
Class B Safety Library, IEC 60730
Functional Safety support (ISO26262)
ASIL-B focused applications
FMEDA and Safety manual
XC16 Functional Safety Compiler
Functional Safety hardware features
Flash with Error Correction Code (ECC)
CodeGuard™ Memory Protection
On-chip Regulator for CPU
Backup FRC and redundant clock sources
Fail Safe Clock Monitor
Windowed Watchdog Timer (WDT)
Windowed Deadman Timer (DMT)
Oscillator Frequency Monitoring through CTMU (OSCI, SYSCLK, FRC, BFRC, LPRC)
BOR and POR
Analog peripherals redundancies
Cyclical Redundancy Check (CRC)
Illegal Opcode Detection
PWM Lock and Dedicated PWM Fault Pin
Internal Loopback to test communication peripherals and IO ports
SFR and Configuration Locks
Address Trap
Math Error Trap
Redundant data storage for Flash-based Configuration bits and Peripheral Pin Select (PPS) Configuration bits

Microchip Technology, Inc Original Stock

Specifications

Category	Integrated Circuits (ICs)EmbeddedMicrocontrollers	Series	Automotive, AEC-Q100, dsPIC™ 33EV, Functional Safety (FuSa)
Core Processor	dsPIC	Core Size	16-Bit
Speed	40 MIPs	Connectivity	I²C, IrDA, LINbus, SPI, UART/USART
Peripherals	Brown-out Detect/Reset, DMA, Motor Control PWM, POR, PWM, WDT	Number of I/O	21
Program Memory Size	128KB (43K x 24)	Program Memory Type	FLASH
EEPROM Size	-	RAM Size	8K x 8
Voltage - Supply (Vcc/Vdd)	4.5V ~ 5.5V	Data Converters	A/D 11x10/12b
Oscillator Type	Internal	Operating Temperature	-40°C ~ 150°C (TA)
Mounting Type	Through Hole	Base Product Number	DSPIC33EV128GM002
Product Category	Digital Signal Processors & Controllers - DSP, DSC	Shipping Restrictions	This product may require additional documentation to export from the United States.
Product	DSCs	Tradename	dsPIC
Mounting Style	Through Hole	Core	dsPIC33E
Number of Cores	1 Core	Maximum Clock Frequency	70 MHz
L1 Cache Instruction Memory	-	L1 Cache Data Memory	-
Data RAM Size	8 kB	Operating Supply Voltage	4.5 V to 5.5 V
Minimum Operating Temperature	- 40 C	Maximum Operating Temperature	+ 85 C
Qualification	AEC-Q100	Data Bus Width	16 bit
Instruction Type	Fixed/Floating Point	Interface Type	Serial
Number of I/Os	21 I/O	Number of Timers/Counters	7 Timer
Product Type	DSP - Digital Signal Processors & Controllers	Factory Pack Quantity	15
Subcategory	Embedded Processors & Controllers	Supply Voltage - Max	5.5 V
Supply Voltage - Min	4.5 V	Watchdog Timers	Watchdog Timer
Programmabe	Not Verified	Package/Case	DIP-28